Start with Arduino DUE

To connect the Arduino Due to your computer, you'll need a Micro-B USB cable. The USB cable will provide power and allow you to program the board.

Attach the USB micro side of the USB cable to the Due's Programming port (this is the port closer to the DC power connector). To upload a sketch, choose Arduino Due (Programming port) from the Tools > Board menu in the Arduino IDE, and select the correct serial port from the Tools > Serial Port menu.

The Due has a dedicated forum for discussing the board.

You must use Arduino IDE 1.5 or later to program the Due.

Differences from ATMEGA based boards

In general, you program and use the Due as you would other Arduino boards. There are, however, a few important differences and functional extensions. 
The Due has the same footprint as the Mega 2560.


The microcontroller mounted on the Arduino Due runs at 3.3V, this means that you can power your sensors and drive your actuartors only with 3.3V. Connecting higher voltages, like the 5V commonly used with the other Arduino boards will damage the Due.

The board can take power from the USB connectors or the DC plug. If using the DC connector, supply a voltage between 7V and 12V.

The Arduino Due has an efficient switching voltage regulator, compliant with the USB host specification. If the Native USB port is used as host by attaching a USB device to the mirco-A usb connector, the board will provide the power to the device. When the board is used as a usb host, external power from the DC connector is required.

Serial ports on the Due

Arduino DUE
The Arduino Due has two USB ports available. The Native USB port (which supports CDC serial communication using the SerialUSB object) is connected directly to the SAM3X MCU. The other USB port is the Programming port. It is connected to an ATMEL 16U2 which acts as a USB-to-Serial converter. This Programming port is the default for uploading sketches and communicating with the Arduino.

The USB-to-serial converter of the Programming port is connected to the first UART of the SAM3X. It's possible to communicate over this port using the "Serial" object in the Arduino programming language.

The USB connector of the Native port is directly connected to the USB host pins of the SAM3X. Using the Native port enables you to use the Due as a client USB peripheral (acting as a mouse or a keyboard connected to the computer) or as a USB host device so that devices can be connected to the Due (like a mouse, keyboard, or an Android phone). This port can also be used as a virtual serial port using the "SerialUSB" object in the Arduino programming language.

Automatic (Software) Reset

The SAM3X microcontroller differs from AVR microcontrollers because the flash memory needs to be erased before being re-programmed. A manual procedure would involve holding the erase button for a second, pressing the upload button in the IDE, then the reset button.

Because a manual erase-flash procedure is repetitive, this is managed automatically by both USB ports, in two different ways:

Native port

Opening and closing the ''Native' port at the baud rate of 1200bps triggers a “soft erase” procedure: the flash memory is erased and the board is restarted with the bootloader. If, for some reason, the MCU were to crash during this process, it is likely that the soft erase procedure wouldn't work as it's done in software by the MCU itself.

Opening and closing the Native port at a baudrate other than 1200bps will not reset the SAM3X. To use the serial monitor, and see what your sketch does from the beginning, you'll need to add few lines of code inside the setup(). This will ensure the SAM3X will wait for the SerialUSB port to open before executing the sketch:

while (!SerialUSB) ;

Pressing the Reset button on the Due causes the SAM3X reset as well as the USB communication. This interruption means that if the serial monitor is open, it's necessary to close and reopen it to restart the communication.

Programming port

The Programming port uses a USB-to-serial chip connected to the first UART of the MCU (RX0 and TX0). The USB-to-serial chip has two pins connected to the Reset and Erase pins of the SAM3X. When you open this serial port, the USB-to-Serial activates the Erase and Reset sequence before it begins communicating with the UART of the SAM3X. This procedure is much more reliable and should work even if the main MCU has crashed.

To communicate serially with the Programming port, use the "Serial" object in the IDE. All existing sketches that use serial communication based on the Uno board should work similarly. The Programming port behaves like the Uno's serial port in that the USB-to-Serial chip resets the board each time you open the serial monitor (or any other serial communication).

Pressing the Reset button while communicating over the Programming port doesn't close a USB connection with the computer because only the SAM3X is reset.

USB Host

The Due has the ability to act as a USB host for peripherals connected to the SerialUSB port. For additional information and examples, see the USB host reference page.

When using the Due as a host, it will be providing power to the attached device. It is strongly recommended to use the DC power connector when acting as a host.

ADC and PWM resolutions

The Due has the ability to change its default analog read and write resolutions (10-bits and 8-bits, respectively). It can support up to 12-bit ADC and PWM resolutions. See the analog write resolution and analog read resolution pages for information.

Expanded SPI functionality

The Due has expanded functionality on its SPI bus, useful for communicating with multiple devices that speak at different speeds. See the Due extended SPI library usage page for more details.

Installing Drivers for the Due


No driver installation is necessary on OSX. Depending on the version of the OS you're running, you may get a dialog box asking you if you wish to open the “Network Preferences”. Click the "Network Preferences..." button, then click "Apply". The Due will show up as “Not Configured”, but it is still working. You can quit the System Preferences.


If you previously installed Arduino IDE, you already have drivers installed.

If you haven't yet installed Arduino IDE, download the Windows version of the Arduino software from the official page here
When the download finishes, launch the file to install the software and the drivers.

If you downloaded the .zip version of the IDE, unzip the downloaded file. Make sure to preserve the folder structure. 
Now your drivers will be downloaded and installed from Internet, directly from Windows. 
If you have issues, you can find the "drivers" folder inside the unzipped file, for manual installation.


No driver installation is necessary for Linux.

In some computers, you need to setup user permissions and some udev rules. 
You can find detailed informations on how to achieve this at this page.

Installing the Arduino Sam Boards core

If you are using the Arduino IDE version 1.6.2 or newer you need to install the core that supports the Arduino Due. Please follow this guide to install the new core.

Uploading Code to the Due

The uploading process on the Arduino Due works the same as other boards from a user's standpoint. It is recommended to use the Programming port for uploading sketches, though you can upload sketches on either of the USB ports.

For uploading with the Programming port follow this steps:

  • Connect your board to the computer by attaching the USB cable to the Due's Programming port (this is the port closer to the DC power connector).
  • Open the Arduino IDE.
  • In the "Tools" menu choose "Serial Port" and select the serial port of the Due
  • Under the "Tools > Boards" menu select "Arduino Due (Programming port)"
  • You are now ready to upload sketches to your Arduino Due.

For more details on the Arduino Due, see the hardware page.